- For use in food and beverage lines, hospitals, OEM machines, chemical processing, feed lines, and laboratory lines
- Can be used in potable water applications
- Good chemical and corrosion-resistance
- Manufactured with FDA compliant material
- Low-density polyethylene construction
- Maximum pressure: 140 psi
- Operating temperature: 42-degrees F to 125-degrees F
- Length: 150-feet
- Outside diameter: 1/4-inch
EZ-FLO 0.170-in ID x 150-ft Polyethylene White Polyethylene Tubing
Rated 4.72 out of 5 based on 25 customer ratings
(26 customer reviews)
$23.98
- For use in food and beverage lines, hospitals, OEM machines, chemical processing, feed lines, and laboratory lines
- Can be used in potable water applications
- Good chemical and corrosion-resistance
SKU: 091712018438
Categories: Pipe & Fittings, Plumbing, Tubing & Hoses
Tags: Black vinyl tubing Tubing & Hoses, Clear vinyl tubing Tubing & Hoses, Disposal hose Tubing & Hoses, EZ-FLO Tubing & Hoses, Flat discharge hose Tubing & Hoses, Flexible schedule 40 hose Tubing & Hoses, Fuel hose Tubing & Hoses, Non-kink pond tubing Tubing & Hoses, Orbit Tubing & Hoses, Polyethylene tubing Tubing & Hoses, Polyurethane Tubing & Hoses, Reinforced air hose Tubing & Hoses, Reinforced braided vinyl tubing Tubing & Hoses, Rubber Tubing & Hoses, Suction hose Tubing & Hoses
The EZ-FLO Polyethylene Tubing can be used in a wide variety of settings involving air and water lines. The white, non-toxic material can withstand chemicals, corrosion, and impact. Some commonly approved applications include: food and beverage lines, hospitals, OEM machines, chemical processing, feed lines, and laboratory lines. Resistant to solvents, acids, alkalis, and fuel. FDA compliant. Can be used in potable water applications. The tubing can be cut as needed.
Weight | 2.63 kg |
---|---|
Dimensions | 7.87 × 7.87 × 3.75 cm |
Brand | EZ-FLO |
26 reviews for EZ-FLO 0.170-in ID x 150-ft Polyethylene White Polyethylene Tubing
Add a review Cancel reply
Related products
Pipe & Fittings
Rated 5.00 out of 5
$19.17
Pipe & Fittings
Rated 4.05 out of 5
$23.98
Fittings & Specialty Tools
Rated 4.95 out of 5
$17.38
$23.98
Rated 4.41 out of 5
$18.48
Pipe & Fittings
Rated 2.63 out of 5
$23.98
Pipe & Fittings
SharkBite 3/4-in x 3/4-in x 3/4-in Push-to-Connect Standard Tee
Rated 4.89 out of 5
$15.38
Pipe & Fittings
Rated 1.00 out of 5
$15.76
Anonymous –
Tubing was very flexible and easy to cut. Did not drip when clamped.
Anonymous –
Kit came with two very short pieces so I had to buy these to replace those shorties. These are 3/8 O.D which was exactly what I needed. Cuts easily with a utility knife, Don’t forget the run a fine sand on the edge just to “deburr” and prevent biting the inside rubber o-ring on the fitting.
Anonymous –
Worked great for my project ! Fits perfectly in the awning rail of our rooftop tent to make a custom annex.
Anonymous –
Nice hose not too heavy but flexible enough to move where I needed it to go
Anonymous –
This EZ-FLO 3/16-in ID x 10-ft Polyethylene Tubing worked as it should have, with the SharkBite 5/16-in OD Push-to-Connect Coupling, Item #835035 Model #25423Z, that I purchased at LOWES too.
Anonymous –
Worked perfectly to attach our RO water filter to our fridge water and ice maker. This tubing has a higher PSI rating than the tubing used to install our RO filter, so I feel safe in knowing I’ve got a leak free solution, and I couldn’t be more pleased.
Anonymous –
Needed to divert some water to a tank and this did the trick.
Anonymous –
Repaired an old cracked water line on my old LG refrigerator
Anonymous –
Good tubing… Temp rating not as high as I wanted…
Anonymous –
I used this on an outdoor water misting system. It’s attached to the faucet and exposed to the morning sun. It has become brittle and cracked in multiple locations at 11 months. Specs say it can operate up to 125F temperature. I don’t think it has any UV protection.
Anonymous –
I needed tubing to connect my icemaker to the water supply. This did the job.
Anonymous –
Worked great. Used it to replace a suction line on my water treatment system.
Anonymous –
I purchased this tubing for a humidifier installation which takes water from my hot water heater to operate more efficiently. Unfortunately most hot water heaters run just above the 125F this tubing is rated for, it cracked and flooded my basement as a result. Probably fine for low temperature applications, do not use with water warmer than luke warm or anywhere a leak would be catastrophic!
Anonymous –
I bought a new Korky toilet gut kit and ended up cutting the black filler tube too short. This tubing was a perfect replacement. Also, it’s always a good Idea to keep some tubing on hand for whatever.
Anonymous –
what I don’t like is that you only stock 25 foot rolls. When I purchase this item, I always need atleast 100 feet at a time.
Anonymous –
It’s an off diameter and a little long for my installation.
Anonymous –
Great tubing I used for an air conditioner drain. Fits snug but to be extra sure I put a clamp over it. Does tend to want to kink into a 90 degree if too much stress is put on it.
Anonymous –
Excellent Quality. Would buy again. This tubing is perfect for a refrigerator ice maker.
Anonymous –
What I wanted
Anonymous –
This is a polyethylene tube that performed exactly how a polyethylene tube should
Anonymous –
If you need ice from the freezer this is your set up. I did have to buy another compression fitting as the first one leaked. Prob user error. Plenty of length in the hose to pull out fridge for cleaning etc.
Anonymous –
I bought this for adding a couple of shutoff valves and a membrane flush bypass valve to my existing reverse osmosis water filter.
The tubing worked well and I can’t tell the difference between this and other pricier options, other than the color. Also all I needed was a couple feet of tubing, this smaller quantity works perfectly for my project.
Anonymous –
The product was the same as described
Anonymous –
Changed an ice maker water line. Worked well.
Anonymous –
Worked to replace old copper water line to a humidifier
Anonymous –
Works pretty good for what I needed it for. It’s fairly cheap and seemed to seal well. Used it for the tubing of a soda fountain machine. The proper stuff wasn’t available but this seems a good substitute maybe even a bit better. Cuts easy and if you warm up the ends a bit they slide right on barbed fittings and with a clamp make a nice seal or you can use push lock fittings which are even easier!